Free picture lesson and practice
How to use a speed square
A speed square marks square and 45° lines, finds angles and lays out roof pitches. Learn the parts, swing the square on screen, then practice reading degrees and roof pitch.
The parts of a speed square
- Lip (fence)
The raised edge you hook over the side of a board so the square sits straight. - Ruler edge
Inch marks along the edge that meets the lip. Most 7 inch squares are marked in eighths. - Pivot point
The corner where the lip edge and ruler edge meet. Hold it against the board when you find an angle. - DEGREES scale
Numbers from 0 to 90 along the long edge. They tell you the angle. - COMMON scale
Roof pitch numbers: inches of rise for every 12 inches of run. - Long edge
The slanted side. It sits at 45° to the lip, so it draws a 45° line.
How to read a speed square, step by step
- Hold the pivot point tight against the edge of the board. Keep it there the whole time.
- Swing the square until the number you want lines up with that same board edge.
- To read an angle, look where the board edge crosses the DEGREES row. Find the numbered mark just before it, then count the small marks. Each small mark is 1°.
- To read a roof pitch, look where the edge crosses the COMMON row. A 6 there means 6 inches of rise for every 12 inches of run, a 6 in 12 pitch.
Quick marks you will use every day
- Square line (90°): hook the lip over the board edge and draw along the ruler edge.
- 45° line: hook the lip over the board edge and draw along the long edge.
- Saw guide: hold the lip against the board and run the base of a circular saw along the ruler edge for a straight crosscut.
Try it yourself
Drag the slider to swing the square on the board. The red line is the board edge. Turn on Snap to roof pitches to see where each COMMON number sits.
Practice reading it
Pick a level, read the square and choose the answer. Every answer comes with the steps.
Roof pitch to degrees
The COMMON number is the rise in inches for every 12 inches of run, so the angle is the arctangent of rise ÷ 12. Here are the pitches most roofs use.
| Pitch (COMMON number) | Angle | Grade |
|---|---|---|
| 1 in 12 | 4.8° | 8.3% |
| 2 in 12 | 9.5° | 16.7% |
| 3 in 12 | 14.0° | 25.0% |
| 4 in 12 | 18.4° | 33.3% |
| 5 in 12 | 22.6° | 41.7% |
| 6 in 12 | 26.6° | 50.0% |
| 7 in 12 | 30.3° | 58.3% |
| 8 in 12 | 33.7° | 66.7% |
| 9 in 12 | 36.9° | 75.0% |
| 10 in 12 | 39.8° | 83.3% |
| 11 in 12 | 42.5° | 91.7% |
| 12 in 12 | 45.0° | 100.0% |
Need another pitch? The slope calculator converts any rise and run to degrees and percent.
Questions
What is the pivot point on a speed square?
It is the corner where the lip edge and the ruler edge meet. When you find an angle or a roof pitch, you hold that corner against the edge of the board and swing the square around it.
What does the COMMON scale mean?
Each COMMON number is the inches of rise for every 12 inches of run. Swing the square until 6 on the COMMON row lines up with the board edge and you are set for a 6 in 12 roof pitch.
How do I draw a 90° line with a speed square?
Hook the lip over the edge of the board and draw along the ruler edge. That line is square to the edge.
How many degrees is a 4 in 12 pitch?
About 18.4°. The angle is the arctangent of 4 ÷ 12.
What is the HIP-VAL row on some squares?
Some squares add a second roof row for hip and valley rafters. This lesson covers the DEGREES and COMMON rows, which are the ones you read most.
Who invented the speed square?
Albert Swanson invented it in 1925, and Swanson Tool Company still makes it.
Keep going
Sources
Measure Drill checks every number against these references or works it out from the exact definitions of the units.