Free picture lesson and practice
How to read a combination square
A combination square blade is a precise steel ruler, often marked down to 1/64 inch. Learn to read the fine edges, slide a mark along the blade, then practice.
The parts of a combination square
- Blade
A steel ruler, often 12 inches long, that slides through the head. - Head
Has a 90° face and a 45° face to hold against the work. - Lock nut
Tighten it to hold the blade at the length you set. - Level vial
A small bubble level in the head on many squares. - Four scales
Many blades have eighths and sixteenths on one side and 32nds and 64ths on the other. A small number at the end of each edge tells you which.
How to read 32nds and 64ths, step by step
- Check which edge you are on. Look for the small 32 or 64 at the end of the edge.
- Find the last whole inch before your mark.
- Jump to the nearest eighth. The longer marks are halves, quarters and eighths, the same as a tape measure. On a 32nds edge, each eighth is 4 small marks. On a 64ths edge, it is 8.
- Count the small marks from that eighth to your mark and add them on.
- Reduce the fraction. 22/32 is 11/16 and 40/64 is 5/8.
Try it yourself
Drag the slider to move the red mark along the blade. The reading shows the fraction and the decimal.
Practice reading it
Pick the 32nds or the 64ths edge, read the red mark and choose the answer.
Using the square
- 90° line: hold the 90° face of the head against a straight edge and draw along the blade.
- 45° line: hold the 45° face against the edge and draw along the blade.
- Depth: rest the head across a hole or groove, slide the blade down to the bottom, lock it and read the blade.
- Marking a line parallel to an edge: set the blade to the distance you want, lock it and slide the head along the edge with a pencil at the end of the blade.
32nds and 64ths in decimals
The odd 32nds, the ones that do not reduce, with the same size in 64ths. For every 64th see the fraction to decimal chart.
| 32nds | Same in 64ths | Decimal | Millimeters |
|---|---|---|---|
| 1/32" | 2/64" | 0.03125" | 0.794 mm |
| 3/32" | 6/64" | 0.09375" | 2.381 mm |
| 5/32" | 10/64" | 0.15625" | 3.969 mm |
| 7/32" | 14/64" | 0.21875" | 5.556 mm |
| 9/32" | 18/64" | 0.28125" | 7.144 mm |
| 11/32" | 22/64" | 0.34375" | 8.731 mm |
| 13/32" | 26/64" | 0.40625" | 10.319 mm |
| 15/32" | 30/64" | 0.46875" | 11.906 mm |
| 17/32" | 34/64" | 0.53125" | 13.494 mm |
| 19/32" | 38/64" | 0.59375" | 15.081 mm |
| 21/32" | 42/64" | 0.65625" | 16.669 mm |
| 23/32" | 46/64" | 0.71875" | 18.256 mm |
| 25/32" | 50/64" | 0.78125" | 19.844 mm |
| 27/32" | 54/64" | 0.84375" | 21.431 mm |
| 29/32" | 58/64" | 0.90625" | 23.019 mm |
| 31/32" | 62/64" | 0.96875" | 24.606 mm |
Questions
How do I read 1/64 on a combination square?
Use the edge marked 64. Each small mark is 1/64". Find the last whole inch, jump to the nearest eighth (8 marks each), count the extra marks and reduce. 26/64 reduces to 13/32.
What is the difference between the 32nds and 64ths edges?
The 32nds edge has 32 marks per inch and the 64ths edge has 64. The 64ths edge is finer, so it is harder to read without good light.
How do I check if my combination square is square?
Draw a line along the blade, flip the square over and draw again from the same point. If the two lines do not match, the square is out.
Is 1/64 inch really that small?
Yes. 1/64" is 0.015625" or about 0.40 mm, a little thicker than a sheet of paper.
Keep going
Sources
Measure Drill checks every number against these references or works it out from the exact definitions of the units.