How to read a caliper

Step by step with pictures: the parts of a caliper, and how to measure the outside of a part, a hole and a depth. Vernier, dial and digital calipers all measure the same way.

How to use a caliper, step by step

1 Know the parts

Inside jawsInside jawsLock screwMain scale on the beamDepth rodOutside jawsOutside jawsVernier scaleThumb roller
The parts of a vernier caliper.

The beam carries the main scale. The sliding jaw moves along it: roll it with the thumb roller and hold it with the lock screw. The big outside jaws measure across a part, the small inside jaws measure holes and slots, and the depth rod comes out of the end to measure how deep something is. The vernier scale on the slide reads the thousandths.

2 The dial caliper version

Inside jawsInside jawsLock screwMain scale on the beamDepth rodOutside jawsOutside jawsDialThumb roller
A dial caliper has the same jaws and rod. The dial replaces the vernier scale.

Dial and digital calipers have the same jaws, rod, roller and lock. Only the way you read the thousandths changes: a vernier scale, a dial or a screen.

3 Measure the outside of a part

The part goes between the outside jaws
Close the outside jaws on the part, near the base of the jaws.
  1. Wipe the jaws, close them and check the caliper reads zero.
  2. Open the jaws wider than the part, then close them gently and squarely on it. Use the part of the jaws near the beam, not the tips.
  3. Light, even pressure. Squeezing hard bends the jaws and reads small.
  4. Read it on the part, or lock it and lift it off.

4 Measure a hole or slot

Inside jaws press out against the walls
Open the small inside jaws until they press out against the walls.

Put the small inside jaws into the hole and open them until they touch both walls. Rock them a little and take the biggest reading, so you are measuring straight across and not at an angle.

5 Measure a depth

Beam end sits flat on topRod touches the bottom of the holeRead the scale as usual
Stand the end of the beam flat on top of the part and slide the rod down to the bottom of the hole.

Set the end of the beam flat on the top surface. Slide the jaw until the depth rod touches the bottom. Keep the caliper straight up and down. The reading on the scale is the depth.

6 Read it

01234560102030405060708090.001 in.100 per turnBar: last mark passed = 1.200"Dial 37 = 0.037"1.200 + 0.037 = 1.237"
Whatever you measured, read the scale the same way. Dial caliper: bar 1.200 + dial 0.037 = 1.237".

Outside, inside and depth are all read from the same scales. Step-by-step pictures: reading a vernier caliper and reading a dial caliper.

Try it yourself

Slide a vernier or a dial caliper and watch the reading change.

The three kinds of caliper

Vernier caliper

A main scale on the beam and a sliding vernier scale. Read the main scale up to the vernier zero, then add the vernier line that lines up exactly. No batteries and no gears, but it takes the most care to read. Vernier caliper steps.

Dial caliper

Read inches and tenths from the bar and thousandths from the dial, then add them. One turn of the needle is 0.100". Dial caliper steps.

Digital caliper

Shows the number on a screen and can switch between inches and millimetres. Still check zero with the jaws closed, know which unit is showing (in or mm), and remember that the last digit can flicker. Being able to read a vernier or dial caliper is still expected on most tests and in many shops.

Calipers or micrometer?

A caliper is quick and measures outside, inside, depth and steps, usually to 0.001" or 0.02 mm. A micrometer does one job (usually outside size) but is more accurate and repeatable. Machinists rough-check with a caliper and confirm with a micrometer.

Practise reading calipers

Questions

What are the three types of calipers?

Vernier, dial and digital. They measure the same way; they only show the number differently.

How accurate is a caliper?

Most inch calipers read to 0.001" and most metric ones to 0.02 mm or 0.01 mm. A micrometer is more accurate for outside measurements.

Can a caliper measure inside a hole?

Yes. The small upper jaws open inside a hole or slot, and the reading is taken from the same scale.

Sources

Measure Drill checks every number against these references or works it out from the exact definitions of the units.