Tap drill chart
Inch threads, UNC and UNF
Tap drill gives about 75% thread for aluminum, brass and plastic. The steel drill gives about 50% thread for tough metals. Close and free are clearance holes.
| Thread | TPI | Tap drill | Inch | Thread | Steel drill | Close | Free |
|---|---|---|---|---|---|---|---|
| #0-80 UNF | 80 | 3⁄64 | .0469 | 81% | #55 | #52 | #50 |
| #1-64 UNC | 64 | #53 | .0595 | 67% | 1⁄16 | #48 | #46 |
| #1-72 UNF | 72 | #53 | .0595 | 75% | #52 | #48 | #46 |
| #2-56 UNC | 56 | #50 | .0700 | 69% | #49 | #43 | #41 |
| #2-64 UNF | 64 | #50 | .0700 | 79% | #48 | #43 | #41 |
| #3-48 UNC | 48 | #47 | .0785 | 76% | #44 | #37 | #35 |
| #3-56 UNF | 56 | #45 | .0820 | 73% | #43 | #37 | #35 |
| #4-40 UNC | 40 | #43 | .0890 | 71% | #41 | #32 | #30 |
| #4-48 UNF | 48 | #42 | .0935 | 68% | #40 | #32 | #30 |
| #5-40 UNC | 40 | #38 | .1015 | 72% | 7⁄64 | #30 | #29 |
| #5-44 UNF | 44 | #37 | .1040 | 71% | #35 | #30 | #29 |
| #6-32 UNC | 32 | #36 | .1065 | 78% | #32 | #27 | #25 |
| #6-40 UNF | 40 | #33 | .1130 | 77% | #31 | #27 | #25 |
| #8-32 UNC | 32 | #29 | .1360 | 69% | #27 | #18 | #16 |
| #8-36 UNF | 36 | #29 | .1360 | 78% | #26 | #18 | #16 |
| #10-24 UNC | 24 | #25 | .1495 | 75% | #20 | #9 | #7 |
| #10-32 UNF | 32 | #21 | .1590 | 76% | #18 | #9 | #7 |
| #12-24 UNC | 24 | #16 | .1770 | 72% | #12 | #2 | #1 |
| #12-28 UNF | 28 | #14 | .1820 | 73% | #10 | #2 | #1 |
| 1⁄4-20 UNC | 20 | #7 | .2010 | 75% | 7⁄32 | F | H |
| 1⁄4-28 UNF | 28 | #3 | .2130 | 80% | #1 | F | H |
| 5⁄16-18 UNC | 18 | F | .2570 | 77% | J | P | Q |
| 5⁄16-24 UNF | 24 | I | .2720 | 75% | 9⁄32 | P | Q |
| 3⁄8-16 UNC | 16 | 5⁄16 | .3125 | 77% | Q | W | X |
| 3⁄8-24 UNF | 24 | Q | .3320 | 79% | S | W | X |
| 7⁄16-14 UNC | 14 | U | .3680 | 75% | 25⁄64 | 29⁄64 | 15⁄32 |
| 7⁄16-20 UNF | 20 | 25⁄64 | .3906 | 72% | 13⁄32 | 29⁄64 | 15⁄32 |
| 1⁄2-13 UNC | 13 | 27⁄64 | .4219 | 78% | 29⁄64 | 33⁄64 | 17⁄32 |
| 1⁄2-20 UNF | 20 | 29⁄64 | .4531 | 72% | 15⁄32 | 33⁄64 | 17⁄32 |
| 9⁄16-12 UNC | 12 | 31⁄64 | .4844 | 72% | 33⁄64 | 37⁄64 | 19⁄32 |
| 9⁄16-18 UNF | 18 | 33⁄64 | .5156 | 65% | 17⁄32 | 37⁄64 | 19⁄32 |
| 5⁄8-11 UNC | 11 | 17⁄32 | .5312 | 79% | 9⁄16 | 41⁄64 | 21⁄32 |
| 5⁄8-18 UNF | 18 | 37⁄64 | .5781 | 65% | 19⁄32 | 41⁄64 | 21⁄32 |
| 3⁄4-10 UNC | 10 | 21⁄32 | .6562 | 72% | 11⁄16 | 49⁄64 | 25⁄32 |
| 3⁄4-16 UNF | 16 | 11⁄16 | .6875 | 77% | 45⁄64 | 49⁄64 | 25⁄32 |
| 7⁄8-9 UNC | 9 | 49⁄64 | .7656 | 76% | 51⁄64 | 57⁄64 | 29⁄32 |
| 7⁄8-14 UNF | 14 | 13⁄16 | .8125 | 67% | 53⁄64 | 57⁄64 | 29⁄32 |
| 1-8 UNC | 8 | 7⁄8 | .8750 | 77% | 59⁄64 | 1 1⁄64 | 1 1⁄32 |
| 1-12 UNF | 12 | 59⁄64 | .9219 | 72% | 61⁄64 | 1 1⁄64 | 1 1⁄32 |
| 1-14 UNS | 14 | 15⁄16 | .9375 | 67% | 61⁄64 | 1 1⁄64 | 1 1⁄32 |
| 1 1⁄8-7 UNC | 7 | 63⁄64 | .9844 | 76% | – | – | – |
| 1 1⁄8-12 UNF | 12 | 1 3⁄64 | 1.0469 | 72% | – | – | – |
| 1 1⁄4-7 UNC | 7 | 1 7⁄64 | 1.1094 | 76% | – | – | – |
| 1 1⁄4-12 UNF | 12 | 1 11⁄64 | 1.1719 | 72% | – | – | – |
| 1 3⁄8-6 UNC | 6 | 1 7⁄32 | 1.2188 | 72% | – | – | – |
| 1 3⁄8-12 UNF | 12 | 1 19⁄64 | 1.2969 | 72% | – | – | – |
| 1 1⁄2-6 UNC | 6 | 1 11⁄32 | 1.3438 | 72% | – | – | – |
| 1 1⁄2-12 UNF | 12 | 1 27⁄64 | 1.4219 | 72% | – | – | – |
Metric threads
Tap drill = size − pitch. The closest inch drill is within 0.008". Clearance holes in mm follow ISO 273.
| Thread | Tap drill | Inch | Closest inch drill | Close mm | Normal mm | Loose mm |
|---|---|---|---|---|---|---|
| M1.6 x 0.35 coarse | 1.25 mm | .0492 | 3⁄64 | 1.7 | 1.8 | 2 |
| M2 x 0.4 coarse | 1.6 mm | .0630 | 1⁄16 | 2.2 | 2.4 | 2.6 |
| M2.5 x 0.45 coarse | 2.05 mm | .0807 | #46 | 2.7 | 2.9 | 3.1 |
| M3 x 0.5 coarse | 2.5 mm | .0984 | #40 | 3.2 | 3.4 | 3.6 |
| M3.5 x 0.6 coarse | 2.9 mm | .1142 | #33 | 3.7 | 3.9 | 4.2 |
| M4 x 0.7 coarse | 3.3 mm | .1299 | #30 | 4.3 | 4.5 | 4.8 |
| M5 x 0.8 coarse | 4.2 mm | .1654 | #19 | 5.3 | 5.5 | 5.8 |
| M6 x 1 coarse | 5 mm | .1969 | #9 | 6.4 | 6.6 | 7 |
| M8 x 1.25 coarse | 6.8 mm | .2677 | H | 8.4 | 9 | 10 |
| M8 x 1 fine | 7 mm | .2756 | J | 8.4 | 9 | 10 |
| M10 x 1.5 coarse | 8.5 mm | .3346 | Q | 10.5 | 11 | 12 |
| M10 x 1.25 fine | 8.8 mm | .3465 | S | 10.5 | 11 | 12 |
| M10 x 1 fine | 9 mm | .3543 | T | 10.5 | 11 | 12 |
| M12 x 1.75 coarse | 10.2 mm | .4016 | Y | 13 | 13.5 | 14.5 |
| M12 x 1.5 fine | 10.5 mm | .4134 | Z | 13 | 13.5 | 14.5 |
| M12 x 1.25 fine | 10.8 mm | .4252 | 27⁄64 | 13 | 13.5 | 14.5 |
| M14 x 2 coarse | 12 mm | .4724 | 15⁄32 | 15 | 15.5 | 16.5 |
| M14 x 1.5 fine | 12.5 mm | .4921 | 31⁄64 | 15 | 15.5 | 16.5 |
| M16 x 2 coarse | 14 mm | .5512 | 35⁄64 | 17 | 17.5 | 18.5 |
| M16 x 1.5 fine | 14.5 mm | .5709 | 37⁄64 | 17 | 17.5 | 18.5 |
| M18 x 2.5 coarse | 15.5 mm | .6102 | 39⁄64 | 19 | 20 | 21 |
| M18 x 1.5 fine | 16.5 mm | .6496 | 21⁄32 | 19 | 20 | 21 |
| M20 x 2.5 coarse | 17.5 mm | .6890 | 11⁄16 | 21 | 22 | 24 |
| M20 x 1.5 fine | 18.5 mm | .7283 | 47⁄64 | 21 | 22 | 24 |
| M22 x 2.5 coarse | 19.5 mm | .7677 | 49⁄64 | 23 | 24 | 26 |
| M22 x 1.5 fine | 20.5 mm | .8071 | 13⁄16 | 23 | 24 | 26 |
| M24 x 3 coarse | 21 mm | .8268 | 53⁄64 | 25 | 26 | 28 |
| M24 x 2 fine | 22 mm | .8661 | 55⁄64 | 25 | 26 | 28 |
| M27 x 3 coarse | 24 mm | .9449 | 15⁄16 | 28 | 30 | 32 |
| M30 x 3.5 coarse | 26.5 mm | 1.0433 | 1 3⁄64 | 31 | 33 | 35 |
Pipe threads, NPT
Drill sizes for tapping without a reamer (ANSI Dryseal recommendations). If you ream first, drill one size smaller. Match pipe size by the outside diameter.
| Pipe size | TPI | Tap drill | Inch | mm | Pipe OD (in) |
|---|---|---|---|---|---|
| 1⁄16" NPT | 27 | C | .2420 | 6.15 | .312 |
| 1⁄8" NPT | 27 | Q | .3320 | 8.43 | .405 |
| 1⁄4" NPT | 18 | 7⁄16 | .4375 | 11.11 | .540 |
| 3⁄8" NPT | 18 | 9⁄16 | .5625 | 14.29 | .675 |
| 1⁄2" NPT | 14 | 45⁄64 | .7031 | 17.86 | .840 |
| 3⁄4" NPT | 14 | 29⁄32 | .9062 | 23.02 | 1.050 |
| 1" NPT | 11.5 | 1 9⁄64 | 1.1406 | 28.97 | 1.315 |
| 1 1⁄4" NPT | 11.5 | 1 31⁄64 | 1.4844 | 37.70 | 1.660 |
| 1 1⁄2" NPT | 11.5 | 1 23⁄32 | 1.7188 | 43.66 | 1.900 |
| 2" NPT | 11.5 | 2 3⁄16 | 2.1875 | 55.56 | 2.375 |
Questions
What size drill for a 1/4-20 tap?
Use a #7 drill (0.201"). It gives about 75% thread. In stainless or tough steel, a 7/32 drill (0.2188") cuts tapping effort with little loss of strength.
What size drill for an M8 tap?
For M8 x 1.25, use a 6.8 mm drill. The rule for metric threads is size minus pitch: 8 − 1.25 = 6.75, rounded to the stock 6.8 mm drill.
What is the tap drill formula?
For inch threads: drill = major diameter − 1 ÷ threads per inch. For metric threads: drill = size − pitch. Both give roughly 75% thread.
What is a clearance hole?
The hole a bolt passes through without threads. A close fit lines parts up accurately; a free or loose fit lets the bolt pass even if the holes are slightly off.
What size drill for a 1/2 NPT tap?
About 45/64" when tapping without a reamer. Pipe sizes are not the thread diameter: a 1/2" NPT thread is about 0.840" across.
More free charts
Sources
Measure Drill checks every number against these references or works it out from the exact definitions of the units.
- Machinery's Handbook (Industrial Press), drill, thread and fastener tables
- NIST Special Publication 811, Appendix B: Conversion factors



